Privacy Policy   |   News Center   |   QL Video   |   Contact Us   |   Quotation consultation   
  • QL- Everywhere in One Waterproof Coating

QL- Everywhere in One Waterproof Coating

Product specification:
Coating amount:
Storage period:
Construction method:
Scope of application:

Contact Hotline
+60 7509 0986
Product catalog

QL- Everywhere in One Waterproof Coating简介

QL- Everywhere in One Waterproof Coating Product introduction

QL- Everywhere in One Waterproof Coating is made of imported raw ingredients which are refined by special equipment, to be made into a high-elastic two-components waterproof coating which is ideal for the drinking water reservoirs green environmental protection.
Product template

QL- Everywhere in One Waterproof Coating Product template



Product Features:
1. When used, mix pre-polymer A and water curing agent B in a ratio of 1:0.2. It is a cured product which can be applied on damp surfaces.
2. 100% environmental-friendly, non-toxic and odourless after curing, non-polluting. It is suitable for waterproofing of drinking water projects and children’s facilities.
3. It has an up to 100% solid content, only a small amount is needed per unit area. Desired thickness can be achieved by one application.
4. The coating has high tensile strength, good ductility and excellent adhesion. It is resistant to heat, cold, chemical erosion and aging. It can prevent mould effectively and retard fire.
5. The original colour of the coating is blue. However, the colour can be customized to the user’s requirements for decorative purpose.
6. It can be used as anti-leak after adding rubber powder; anti-slip layer after adding sand or insulation coating after adding light airy fillers.
7. It is easy to use, labour-saving, time-saving, cost-saving and safe.
Scope of application

QL- Everywhere in One Waterproof CoatingScope of application



Application To:
1. Especially suitable for waterproofing of drinking water reservoirs and places with special environmental protection requirements, and it complies with VOC limit value;
2. Overall waterproofing and moisture-proofing of roof, kitchen and bathroom, basement, exterior wall, floor, gutter, balcony, planter, swimming pool, cold store and etc;
3. Repair of cracks in buildings, sealing of expansion joints;
4. Protect various pipes against corrosion.
Construction tools

QL- Everywhere in One Waterproof CoatingConstruction requirements



Application Methods:
1. Surface preparation: the surface must be firm, clean, and free of dust, oil, sand and water.  Defects such as cracks should be repaired first, internal and external corners to be made round;
2. Stir the coating in the container thoroughly before use to prevent precipitation. Mix A and B using ratio 1:0.2 and apply the coating with a brush or scraper.
3. The coating can be set in one application on horizontal surface. In order to prevent dripping, apply a very thin coat on vertical surface. After approximate 5-10 minutes (depending on the temperature of the site and the environment) the mixture is left in the container, apply another coat on the first layer based on the required thickness for the design. On that, the thickness required for the design is once applied to the base layer; it should be after 24 hours (when the first layer is non-sticky to feet). Walking on it is not allowed when it is not fully cured;
4. Use 1:2.5 cement mortar with a thickness of 20mm or other materials as the protective layer, or expose it without a protective layer, the colour of the paint will change;
5. Recommended consumption: 1.5kg/㎡~2.0kg/㎡ (thickness 1.2mm~1.8mm).



Recommended Tools:
Brush, spatula, float trowel, electronic mixer, mixing bucket  

QL- Everywhere in One Waterproof CoatingTechnical index

Technical Indicators:
Experimental Project Technical Specifications
 (%)
Solid Content
≥92
 
 (h)
Tack-free time
12
 (h)
Hard drying time
24
(MPa)
Tensile Strength
≥2
 (%)
Elongation of Break
≥500
 

QL- Everywhere in One Waterproof Coating store up and transport


Packaging and transportation:
1. For storage, seal the bucket to prevent moisture absorption and contamination, store it in a ventilated and cool warehouse;
2. This product can be stored for 12 months and it still can be used after the storage period should it passes relevant tests;
3. This product is non-flammable. Avoid collision and keep away from sunlight and rain during delivery, keep the packing intact;
4. Specification: 1kg / set; with brush, stirrer and gloves.

QL- Everywhere in One Waterproof Coating Matters needing attention


Notice: 
1. The mixture must be used within 30 minutes. Clean the tools and container with detergent or lipid cleaner;
2. It is normal to have precipitation in the container and it does not affect normal use;
3. Ambient temperature shall be higher than 5℃.